65 mm tiny whoop motor
Tiny Whoop Onesies 0702
A one-piece-bell 702 for 65 mm whoops, 1.45 g with Tiny Whoop's short 23 mm leads, with solder pads under the silicone for repairs and wire swaps.
- 65 mm whoops
- Light builds: Tiny Whoop suggests a dry weight under 18 g
The spin is an illustration: the model turns at 1/600 of the no-load speed, and it is a generic 0702 motor drawn from Tiny Whoop’s published sizes, not its exact design. No-load speed is KV × 3.7 V, a nominal pack for this version. Tiny Whoop publishes no bench data for it.
- Weight
- 1.454 g
- V2 with 23 mm leads; 1.5364 g for V1 with 32 mm leads. The Elements Series (26,000KV) has a bell 0.0441 g lighter.
from $39.99a motor at Tiny Whoop
A set of four: $159.96
Price seen Oct 19, 2026. Plain links: we earn nothing from them.
What you get for $39.99
PCB solder pads
Peel back the black silicone to reach the pads where the leads join the motor, for repairs or custom wire colours.
Short V2 leads
23 mm leads bring the weight from 1.5364 g (V1, 32 mm leads) to 1.4538 g; Tiny Whoop says they won't reach on builds bigger than 65 mm.
Weight off the edges
Tiny Whoop says a 603 or 802 makes the same thrust more efficiently, but the 702's lower weight far from the centre lets the quad change attitude faster.
One-piece bell
The bell is one piece, as the box says.
Source: Tiny Whoop product photo
What to pair it with
Our reading of Tiny Whoop’s numbers, so your build matches what the motor was tested with.
- Frame
- 65 mm whoops: a three-hole base, and V2 leads too short for bigger builds. (Tiny Whoop product page (19,000KV), Tiny Whoop base photo)
- Battery
- Tiny Whoop says it made the 26,000KV to hold a high speed for two minutes on its 300 mAh pack; the 27,000KV is slightly faster. (Tiny Whoop product page (27,000KV))
- Props
- 1 mm shaft on every edition but the 27,000KV Positronic, which needs props for a 1.5 mm shaft. (Tiny Whoop product page (27,000KV))
- ESC
- Tiny Whoop publishes no current draw or bench data for the 702 Onesies. (Tiny Whoop product page (23,000KV))
Where to buy
- Tiny Whoopthe maker's store; 23,000KV Cricket Edition, set of 4$39.99seen Oct 19, 2026Visit
Plain links, not affiliate links. Prices change; the store’s page has the current one.
Full specs
| Spec | Value | Source |
|---|---|---|
| KV | 23,000 rpm/V (also 19,000, 21,500, 25,250, 26,000, 27,000 (1.5 mm shaft) and 28,500KV, each a named edition) | Tiny Whoop product page (23,000KV) |
| Stator | 7 × 2 mm (0702) (size from the 702 in Tiny Whoop's name) | Tiny Whoop product page (23,000KV) |
| Weight | 1.454 g (V2 with 23 mm leads; 1.5364 g for V1 with 32 mm leads. The Elements Series (26,000KV) has a bell 0.0441 g lighter.) | Tiny Whoop product page (19,000KV) |
| Shaft | 1 mm (Tiny Whoop's standard size); 1.5 mm on the 27,000KV Positronic edition | Tiny Whoop product page (27,000KV) |
| Mounting | 3 screw holes in a triangular base (read off Tiny Whoop's photo of the base; no hole size or spacing is published) | Tiny Whoop base photo |
| Bell | One piece ("1-piece bell" on the box) | Tiny Whoop product photo |
| Leads | 3 leads soldered to PCB pads under a silicone cover, with a plug: 23 mm on V2, 32 mm on V1 (Tiny Whoop says the 23 mm leads won't reach on builds bigger than 65 mm) | Tiny Whoop product page (19,000KV) |
| In the box | 4 motors with screws (read off the product photo) | Tiny Whoop product photo |
Inside the motor
A brushless outrunner: the coils stand still in the middle and the magnets spin around them. From the top down:
- Bell. One piece. (Tiny Whoop product photo)
- Base. Triangular, with three screw holes and PCB solder pads where the leads join, under a silicone cover. (Tiny Whoop product page (23,000KV), Tiny Whoop base photo)
- Leads. 23 mm on V2; 32 mm on V1, still sold on some editions. (Tiny Whoop product page (19,000KV))
How fast it spins
KV is the motor’s no-load speed per volt. With nothing on the shaft, the 23000KV version reaches about these speeds; a prop loads the motor and brings it down, typically to around 70–75% of these figures at full throttle.
| Battery | Volts | No-load rpm (KV × V) | Electrical frequency | ESC steps per second |
|---|---|---|---|---|
| 4S nominal | 14.8 | 340,400 | 34,040 Hz | 204,240 |
| 4S full | 16.8 | 386,400 | 38,640 Hz | 231,840 |
| 6S nominal | 22.2 | 510,600 | 51,060 Hz | 306,360 |
| 6S full | 25.2 | 579,600 | 57,960 Hz | 347,760 |
A 12-pole rotor has 6 pole pairs, so every turn of the shaft is 6 electrical cycles, and a six-step ESC switches the phases 36 times per turn.
About the 3D model
A generic outrunner drawn from Tiny Whoop’s published sizes: the 7 × 2 mm stator and 1 mm shaft. Anything Tiny Whoop doesn’t publish is typical for a motor this size, and the bell’s spoked top, the base and the inside are a generic design, not this motor’s. The colours are read off the maker’s product photos. There are no logos or markings: it is our drawing, not the maker’s.
Sources
- Tiny Whoop: 702 23,000kv Tiny Whoop Onesies Brushless Motors - Cricket Edition (product page on Tiny Whoop's own store). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 19,000kv Tiny Whoop Onesies Brushless Motors - Semiplume Edition (product page, with the V1 and V2 lead lengths and weights). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 21,500kv Tiny Whoop Onesies Brushless Motors - Cumulous Edition (product page). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 25,250kv Tiny Whoop Onesies Brushless Motors - Zia Edition (product page). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 26,000kv Carbon Edition Tiny Whoop Onesies Brushless Motors, Elements Series (product page). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 26,000kv Silver Edition Tiny Whoop Onesies Brushless Motors, Elements Series (product page). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 26,000kv Neon Edition Tiny Whoop Onesies Brushless Motors, Elements Series (product page). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 27000kv *1.5mm SHAFT* Tiny Whoop Onesies Brushless Motors - Positronic Limited Edition (product page). Retrieved Oct 19, 2026.
- Tiny Whoop: 702 28,500 Tiny Whoop Onesies Brushless Motors - Phoenicopter Limited Edition (product page). Retrieved Oct 19, 2026.
- Tiny Whoop: Cricket Edition main product photo, four motors, screws and the box marked "1-piece bell" (image on S1), used for finish. Retrieved Oct 19, 2026.
- Tiny Whoop: photo of a Onesie's base with its PCB solder pads (image on every Onesie page). Retrieved Oct 19, 2026.
