8- to 10-inch cinematic FPV motor
Lumenier ZIP V2 3115
A 98 g 3115 in matte black for 8- to 10-inch cinematic builds on 6S: 12N14P, N52H arc magnets, a hollow titanium-alloy shaft and NMB bearings, in 900KV and 1050KV.
- 8- to 10-inch props on 6S
- Cinematic builds
- 19 × 19 mm M3 motor mounts
The spin is an illustration: the model turns at 1/600 of the no-load speed, and it is a generic 3115 motor drawn from Lumenier’s published sizes, not its exact design. No-load speed is KV × 22.2 V, a nominal pack for this version. Lumenier publishes no bench data for it.
- Weight
- 98 g
- with short wires
from $51.99a motor at Lumenier
A set of four: $207.96
Price seen Oct 19, 2026. Plain links: we earn nothing from them.
What you get for $51.99
8–10-inch props on 6S
Lumenier says the 3115 works well with 8- to 10-inch props on 6S; it is rated for 4S–6S.
Source: Lumenier product page
Hollow titanium shaft
The hollow titanium-alloy shaft takes a regular prop nut; Lumenier says its threads won't strip, and a screw holds it in for easy maintenance.
Source: Lumenier product page
Matte black
Lumenier's Cinematic Series motors are all black so they don't draw attention in shots.
Source: Lumenier product page
Balanced at the factory
Lumenier says each motor is dynamically balanced and tested before it ships.
Source: Lumenier product page
What to pair it with
Our reading of Lumenier’s numbers, so your build matches what the motor was tested with.
- Props
- 8- to 10-inch props, by Lumenier's own note, on a 5 mm shaft threaded for a nut; a low-profile and a standard locking prop nut come in the box. (Lumenier product page)
- Battery
- 6S, which Lumenier names for 8- to 10-inch props; rated for 4S–6S. (Lumenier product page)
- Frame
- A 19 × 19 mm bolt pattern with M3 screws; four M3×8 screws come in the box. (Lumenier product page)
Where to buy
- Lumenierthe maker's store; same price for both KVs$51.99seen Oct 19, 2026Visit
- GetFPVLumenier's sister store; 900KV or 1050KV$51.99seen Oct 19, 2026Visit
Plain links, not affiliate links. Prices change; the store’s page has the current one.
Full specs
| Spec | Value | Source |
|---|---|---|
| KV | 900 rpm/V (also 1050KV) | Lumenier product page |
| Stator | 31 × 15 mm (3115), 0.2 mm Kawasaki silicon-steel laminations | Lumenier product page |
| Configuration | 12N14P (12 stator slots, 14 magnet poles) | Lumenier product page |
| Battery | 4S–6S LiPo (Lumenier says the 3115 works well with 8–10-inch props on 6S) | Lumenier product page |
| Weight | 98 g (with short wires) | Lumenier product page |
| Shaft | Hollow titanium alloy, 5 mm at the prop, threaded for a prop nut; inner shaft 4.8 mm; held in by a screw | Lumenier product page |
| Mounting | 19 × 19 mm, M3 | Lumenier product page |
| Bell | 7075 aluminium bell and base, anodised matte black | Lumenier product page |
| Magnets | N52H arc magnets | Lumenier product page |
| Bearings | Japanese NMB, 11 × 5 × 5 mm | Lumenier product page |
| Leads | 18 AWG, 200 °C wire, 50 cm total length, bare ends | Lumenier product page |
| In the box | A low-profile and a standard locking prop nut, 4 × M3×8 mounting screws, a spacer/washer | Lumenier product page |
Inside the motor
A brushless outrunner: the coils stand still in the middle and the magnets spin around them. From the top down:
- Shaft. Hollow titanium alloy, 5 mm at the prop, threaded for a prop nut; inner shaft 4.8 mm; held in by a screw. (Lumenier product page)
- Bell. 7075 aluminium bell and base, anodised matte black. (Lumenier product page)
- Magnets. N52H arc magnets. (Lumenier product page)
- Stator. The coils are wound on a stack of thin steel laminations: 31 × 15 mm (3115), 0.2 mm Kawasaki silicon-steel laminations. (Lumenier product page)
- Bearings. Japanese NMB, 11 × 5 × 5 mm. (Lumenier product page)
- Base. 19 × 19 mm, M3. (Lumenier product page)
How fast it spins
KV is the motor’s no-load speed per volt. With nothing on the shaft, the 900KV version reaches about these speeds; a prop loads the motor and brings it down, typically to around 70–75% of these figures at full throttle.
| Battery | Volts | No-load rpm (KV × V) | Electrical frequency | ESC steps per second |
|---|---|---|---|---|
| 4S nominal | 14.8 | 13,320 | 1,554 Hz | 9,324 |
| 4S full | 16.8 | 15,120 | 1,764 Hz | 10,584 |
| 6S nominal | 22.2 | 19,980 | 2,331 Hz | 13,986 |
| 6S full | 25.2 | 22,680 | 2,646 Hz | 15,876 |
A 14-pole rotor has 7 pole pairs, so every turn of the shaft is 7 electrical cycles, and a six-step ESC switches the phases 42 times per turn.
About the 3D model
A generic outrunner drawn from Lumenier’s published sizes: the 31 × 15 mm stator, 5 mm shaft, 19 mm mounting circle and 12 teeth and 14 magnets. Anything Lumenier doesn’t publish is typical for a motor this size, and the bell’s spoked top, the base and the inside are a generic design, not this motor’s. The colours are read off the maker’s product photos. There are no logos or markings: it is our drawing, not the maker’s.
Sources
- Lumenier: ZIP V2 3115 Cinematic Motor - 900KV/1050KV (product page). Retrieved Oct 19, 2026.
- Lumenier: ZIP V2 3115 900KV main product photo, used for finish. Retrieved Oct 19, 2026.
- Lumenier: ZIP V2 3115 photos of the top (900KV and 1050KV, on the product page), used for the spoke count. Retrieved Oct 19, 2026.
