5-inch FPV freestyle motor
Lumenier ZIP V2 2407 Blackout
A 37 g, all-black 2407 for 6S: 12N14P, N52SH curved magnets, NMB bearings and a 5 mm prop shaft on a 4 mm titanium-alloy inner shaft.
- 5-inch freestyle
- 6S (rated 3S–8S)
- Builds where the motors shouldn't stand out
The spin is an illustration: the model turns at 1/600 of the no-load speed, and it is a generic 2407 motor drawn from Lumenier’s published sizes, not its exact design. No-load speed is KV × 22.2 V, a nominal pack for this version. Lumenier publishes no bench data for it.
- Weight
- 37 g
- with short wires
Plain links: we earn nothing from them.
What you get
Blackout finish
All black, with no colour on the bell; Lumenier pitches the look for professional use.
Source: Lumenier product page
N52SH magnets
Curved N52SH magnets; Lumenier chose the SH grade for its temperature rating.
Source: Lumenier product page
37 g
Lumenier lists 37 g per motor with short wires.
Source: Lumenier product page
Balanced at the factory
Lumenier says each motor is dynamically balanced and tested before it ships.
Source: Lumenier product page
What to pair it with
Our reading of Lumenier’s numbers, so your build matches what the motor was tested with.
- Battery
- 6S, which Lumenier calls the most common for the 1700KV; rated for 3S–8S. (Lumenier product page)
- Props
- Regular props with a 5 mm hole on the M5 prop shaft. (Lumenier product page)
- Frame
- A 16 × 16 mm bolt pattern with M3 screws. (Lumenier product page)
Where to buy
- Lumenierthe maker's store; out of stock on the day checked$29.99seen Oct 19, 2026Visit
- GetFPVLumenier's sister store; out of stock on the day checked$29.99seen Oct 19, 2026Visit
Plain links, not affiliate links. Prices change; the store’s page has the current one.
Full specs
| Spec | Value | Source |
|---|---|---|
| KV | 1,700 rpm/V | Lumenier product page |
| Stator | 24 × 7 mm (2407), 0.2 mm Kawasaki silicon-steel laminations | Lumenier product page |
| Configuration | 12N14P (12 stator slots, 14 magnet poles) | Lumenier product page |
| Battery | 3S–8S LiPo (6S most common for 1700KV) | Lumenier product page |
| Weight | 37 g (with short wires) | Lumenier product page |
| Dimensions | 32 × 29 mm (Lumenier's figure; it doesn't say which two sizes these are) | Lumenier product page |
| Shaft | 5 mm prop shaft for M5 props, on a 4 mm titanium-alloy inner shaft | Lumenier product page |
| Mounting | 16 × 16 mm, M3 | Lumenier product page |
| Bell | Anodised aluminium bell and base (7075 base casing), all black | Lumenier product page |
| Magnets | N52SH curved magnets | Lumenier product page |
| Bearings | Japanese NMB, 9 × 4 × 4 mm | Lumenier product page |
| Leads | 18 AWG, 160 mm, bare wire | Lumenier product page |
| In the box | One motor and a hardware set | Lumenier product page |
Inside the motor
A brushless outrunner: the coils stand still in the middle and the magnets spin around them. From the top down:
- Shaft. 5 mm prop shaft for M5 props, on a 4 mm titanium-alloy inner shaft. (Lumenier product page)
- Bell. Anodised aluminium bell and base (7075 base casing), all black. (Lumenier product page)
- Magnets. N52SH curved magnets. (Lumenier product page)
- Stator. The coils are wound on a stack of thin steel laminations: 24 × 7 mm (2407), 0.2 mm Kawasaki silicon-steel laminations. (Lumenier product page)
- Bearings. Japanese NMB, 9 × 4 × 4 mm. (Lumenier product page)
- Base. 16 × 16 mm, M3. (Lumenier product page)
How fast it spins
KV is the motor’s no-load speed per volt. With nothing on the shaft, the 1700KV version reaches about these speeds; a prop loads the motor and brings it down, typically to around 70–75% of these figures at full throttle.
| Battery | Volts | No-load rpm (KV × V) | Electrical frequency | ESC steps per second |
|---|---|---|---|---|
| 4S nominal | 14.8 | 25,160 | 2,935 Hz | 17,612 |
| 4S full | 16.8 | 28,560 | 3,332 Hz | 19,992 |
| 6S nominal | 22.2 | 37,740 | 4,403 Hz | 26,418 |
| 6S full | 25.2 | 42,840 | 4,998 Hz | 29,988 |
A 14-pole rotor has 7 pole pairs, so every turn of the shaft is 7 electrical cycles, and a six-step ESC switches the phases 42 times per turn.
About the 3D model
A generic outrunner drawn from Lumenier’s published sizes: the 24 × 7 mm stator, 5 mm shaft, 16 mm mounting circle and 12 teeth and 14 magnets. Anything Lumenier doesn’t publish is typical for a motor this size, and the bell’s spoked top, the base and the inside are a generic design, not this motor’s. The colours are read off the maker’s product photos. There are no logos or markings: it is our drawing, not the maker’s.
Sources
- Lumenier: ZIP V2 2407 Blackout Motor - 1700KV (product page). Retrieved Oct 19, 2026.
- Lumenier: ZIP V2 2407 Blackout main product photo, used for finish. Retrieved Oct 19, 2026.
- Lumenier: ZIP V2 2407 Blackout "Bell upgrades" diagram of the bell top (image on the product page), used for the spoke count. Retrieved Oct 19, 2026.
