Cinewhoop motor
Lumenier ZIP V2 1404
An 8.3 g, all-black 1404 for micro cinematic builds: 9N12P, N52H arc magnets, NSK bearings, and a 1.5 mm shaft with a T-mount for micro props.
- Micro cinematic builds
- Micro props with a T-mount (M2, 5 mm)
- 9 × 9 mm M2 motor mounts
The spin is an illustration: the model turns at 1/600 of the no-load speed, and it is a generic 1404 motor drawn from Lumenier’s published sizes, not its exact design. No-load speed is KV × 22.2 V, a nominal pack for this version. Lumenier publishes no bench data for it.
- Weight
- 8.3 g
from $22.49a motor at GetFPV
A set of four: $89.96
Price seen Oct 19, 2026. Plain links: we earn nothing from them.
What you get for $22.49
Matte black
Lumenier's Cinematic Series motors are all black so they don't draw attention in shots.
Source: Lumenier product page
T-mount props
Props bolt on with M2 screws 5 mm apart; a screw set comes in the box.
Source: Lumenier product page
8.3 g
Lumenier lists 8.3 g per motor.
Source: Lumenier product page
Balanced at the factory
Lumenier says each motor is dynamically balanced and tested before it ships.
Source: Lumenier product page
What to pair it with
Our reading of Lumenier’s numbers, so your build matches what the motor was tested with.
- Props
- Micro props with a T-mount: M2 holes, 5 mm eye to eye. (Lumenier product page)
- Frame
- A 9 × 9 mm bolt pattern with M2 screws. (Lumenier product page)
Where to buy
- Lumenierthe maker's store; out of stock on the day checked$22.49seen Oct 19, 2026Visit
- GetFPVLumenier's sister store; 2750KV or 4600KV$22.49seen Oct 19, 2026Visit
Plain links, not affiliate links. Prices change; the store’s page has the current one.
Full specs
| Spec | Value | Source |
|---|---|---|
| KV | 2,750 rpm/V (also 4600KV; the spec list reads "2650 or 4600", the title and options 2750KV or 4600KV) | Lumenier product page |
| Stator | 14 × 4 mm (1404), 0.15 mm Nippon silicon-steel laminations (the stator size is GetFPV's "Motor Stator Size: 1404") | GetFPV (Lumenier) page |
| Configuration | 9N12P (9 stator slots, 12 magnet poles) | Lumenier product page |
| Weight | 8.3 g | Lumenier product page |
| Shaft | 1.5 mm, with a T-mount for props (M2 holes, 5 mm eye to eye) | Lumenier product page |
| Mounting | 9 × 9 mm, M2 | Lumenier product page |
| Bell | Al 7075 bell cap and base casing, matte black | Lumenier product page |
| Magnets | N52H arc magnets | Lumenier product page |
| Bearings | Japanese NSK, 5 × 2 × 2.5 mm | Lumenier product page |
| Leads | 30 AWG, 10 cm | Lumenier product page |
| In the box | M2 screw set for the props and the motor | Lumenier product page |
Inside the motor
A brushless outrunner: the coils stand still in the middle and the magnets spin around them. From the top down:
- Shaft. 1.5 mm, with a T-mount for props (M2 holes, 5 mm eye to eye). (Lumenier product page)
- Bell. Al 7075 bell cap and base casing, matte black. (Lumenier product page)
- Magnets. N52H arc magnets. (Lumenier product page)
- Stator. The coils are wound on a stack of thin steel laminations: 14 × 4 mm (1404), 0.15 mm Nippon silicon-steel laminations (the stator size is GetFPV's "Motor Stator Size: 1404"). (GetFPV (Lumenier) page)
- Bearings. Japanese NSK, 5 × 2 × 2.5 mm. (Lumenier product page)
- Base. 9 × 9 mm, M2. (Lumenier product page)
How fast it spins
KV is the motor’s no-load speed per volt. With nothing on the shaft, the 2750KV version reaches about these speeds; a prop loads the motor and brings it down, typically to around 70–75% of these figures at full throttle.
| Battery | Volts | No-load rpm (KV × V) | Electrical frequency | ESC steps per second |
|---|---|---|---|---|
| 4S nominal | 14.8 | 40,700 | 4,070 Hz | 24,420 |
| 4S full | 16.8 | 46,200 | 4,620 Hz | 27,720 |
| 6S nominal | 22.2 | 61,050 | 6,105 Hz | 36,630 |
| 6S full | 25.2 | 69,300 | 6,930 Hz | 41,580 |
A 12-pole rotor has 6 pole pairs, so every turn of the shaft is 6 electrical cycles, and a six-step ESC switches the phases 36 times per turn.
About the 3D model
A generic outrunner drawn from Lumenier’s published sizes: the 14 × 4 mm stator, 1.5 mm shaft, 9 mm mounting circle and 9 teeth and 12 magnets. Anything Lumenier doesn’t publish is typical for a motor this size, and the bell’s spoked top, the base and the inside are a generic design, not this motor’s. The colours are read off the maker’s product photos. There are no logos or markings: it is our drawing, not the maker’s.
Sources
- Lumenier: ZIP V2 1404 Micro Cinematic Motor - 2750KV/4600KV (product page). Retrieved Oct 19, 2026.
- GetFPV (Lumenier's own store): Lumenier ZIP V2 1404 Micro Cinematic Motor - 2750KV/4600KV (product page, read through r.jina.ai). Retrieved Oct 19, 2026.
- Lumenier: ZIP V2 1404 2750KV main product photo, used for finish. Retrieved Oct 19, 2026.
