BrotherHobby SE 2807

What it pulls

BrotherHobby’s own bench test, one line per prop. Drag across the chart to move the throttle; the model above follows.

What you get for $16.00

• 2.5 kg on a 7-inch prop

  On BrotherHobby’s 6S bench the 1300KV pulled 2,538 g at full throttle on an HQ 7 × 3.5 × 3, drawing 42.2 A.

  Source: BrotherHobby test report, BrotherHobby thrust summary

• 48 g with leads

  BrotherHobby gives 48 g with 200 mm leads.

  Source: BrotherHobby product page, BrotherHobby thrust summary, BrotherHobby test report

• Hard-anodised 7075

  Bell cap and base in 7075 aluminium with a hard-anodised finish, on a SUS420 heat-treated steel shaft.

  Source: BrotherHobby product page, BrotherHobby infographic and drawing

• Balanced to 3 mg

  The test report gives a dynamic-balance standard of 3 mg or less, insulation resistance of 0.5 MΩ or more and a passed coil test.

  Source: BrotherHobby test report

What to pair it with

Our reading of BrotherHobby’s numbers, so your build matches what the motor was tested with.

ESC

BrotherHobby lists a 6S 50 A ESC; the full-throttle peak was 42.2 A. (BrotherHobby test report)

Props

BrotherHobby pairs it with 7-inch props and tested it on an HQ 7 × 3.5 × 3: 2,538 g at full throttle. (BrotherHobby prop image, BrotherHobby test report)

Battery

6S. (BrotherHobby product page, BrotherHobby test report)

Frame

Four M3 holes on a 19 mm circle (19 × 19 mm); four M3 × 8 screws and an M5 flange nut come in the box. (BrotherHobby product page, BrotherHobby infographic and drawing, BrotherHobby packing list)

Where to buy

• BrotherHobbythe maker’s store
  $16.00seen Oct 19, 2026
  Visit

Plain links, not affiliate links. Prices change; the store’s page has the current one.

Full specs

Bench data

Redrawn from BrotherHobby’s test reports. Thrust is static pull on a bench, more than you get in flight. Power is volts × amps; efficiency is thrust divided by power.

Inside the motor

A brushless outrunner: the coils stand still in the middle and the magnets spin around them. From the top down:

• Bell. 7075 aluminium bell cap, φ33.2 mm, hard anodised, with five spokes. (BrotherHobby product page, BrotherHobby infographic and drawing)
• Shaft. SUS420 heat-treated steel with an M5 thread, standing 14 mm above the bell. (BrotherHobby product page, BrotherHobby infographic and drawing)
• Magnets. N52H arc magnets, 14 poles. (BrotherHobby product page, BrotherHobby infographic and drawing)
• Stator. 28 × 7 mm with 12 slots, in 0.2 mm Kawasaki silicon steel, wound with TU1-grade enamelled wire. (BrotherHobby product page, BrotherHobby infographic and drawing, BrotherHobby test report)
• Bearings. NMB, 12 × 6 × 4 mm. (BrotherHobby product page)
• Base. 7075 aluminium, with four M3 holes on a 19 mm circle and 18 AWG leads 200 mm long. (BrotherHobby product page, BrotherHobby infographic and drawing)

How fast it spins

KV is the motor’s no-load speed per volt. With nothing on the shaft, the 1300KV version reaches about these speeds; a prop loads the motor and brings it down, typically to around 70–75% of these figures at full throttle.

A 14-pole rotor has 7 pole pairs, so every turn of the shaft is 7 electrical cycles, and a six-step ESC switches the phases 42 times per turn.

About the 3D model

A generic outrunner drawn from BrotherHobby’s published sizes: the 28 × 7 mm stator, 33.2 mm bell, 19.35 mm height, 5 mm shaft, 19 mm mounting circle and 12 teeth and 14 magnets. Anything BrotherHobby doesn’t publish is typical for a motor this size, and the bell’s spoked top, the base and the inside are a generic design, not this motor’s. The colours are read off the maker’s product photos. There are no logos or markings: it is our drawing, not the maker’s.

Sources

1. BrotherHobby: SE 2807 1300KV Motor (CW) (product page on BrotherHobby’s store, with its spec list, photos and Test Data tab). Retrieved Oct 19, 2026.
2. BrotherHobby: SE 2807 weight, maximum thrust and full-throttle summary (image on the product page). Retrieved Oct 19, 2026.
3. BrotherHobby: SE 2807 “paired with 7 inch prop” (image on the product page). Retrieved Oct 19, 2026.
4. BrotherHobby: SE 2807 exploded view (shaft, caps, magnets, bearings, wire, stator steel) and dimension drawing (image on the product page). Retrieved Oct 19, 2026.
5. BrotherHobby: SE 2807 packing list (image on the product page). Retrieved Oct 19, 2026.
6. BrotherHobby: SE 2807-1300KV test report on 6S with an HQ 7 × 3.5 × 3, 2022 bench, with drawing and spec table (image on the Test Data tab). The copper temperature is after two minutes at full throttle.. Retrieved Oct 19, 2026.